How to configure Static Routing with 4 router in Cisco Packet Tracer


Hello guys today we will learn how can we configure static routing in Cisco Packet Tracer .so here i take four router and four PC and connect each-other.so according to condition  i have eight (8) network so i just configure static routeing in this .

ststic routing

here we will also provide ip address for pc  provide

pc0 = ip address is  5.0.0. default ip 5.0.0.1

pc1=ip address 6.0.0.2 default  ip 6.0.0.1

pc2= ip address 7.0.0.2 default ip 7.0.0.1

pc3= ip address 8.0.0.2 default ip 8.0.0.2

Step 1 Here now i am going to router in  0 and provide ip address

Router>enable
 Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface FastEthernet0/0
 Router(config-if)#ip address 8.0.0.1 255.0.0.0
 Router(config-if)#no shutdown
Router(config-if)#
 %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
 Router(config)#interface Serial0/0/0
 Router(config-if)#ip address 3.0.0.2 255.0.0.0
 Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
Router(config-if)#exit
 Router(config)#interface Serial0/0/1
Router(config-if)#
 %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
 ip address 4.0.0.1 255.0.0.0
Router(config-if)#no shutdown

Step 1 Here now i am going to router in  1 and provide ip address

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface Serial0/0/1
Router(config-if)#ip address 1.0.0.1 255.0.0.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
Router(config-if)#
 Router(config-if)#exit
 Router(config)#interface Serial0/0/0
 Router(config-if)#ip address 4.0.0.2 255.0.0.0
 Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
Router(config-if)#
 Router(config-if)#exit
 Router(config)#interface FastEthernet0/0
 Router(config-if)#ip address 5.0.0.1 255.0.0.0
 Router(config-if)#no shutdown

 
Step 1 Here now i am going to router in  2and provide ip address

 Router>enable
 Router#configure terminal
Router(config)#interface FastEthernet0/0
 Router(config-if)#ip address 7.0.0.1 255.0.0.0
 Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
 Router(config)#interface Serial0/0/1
 Router(config-if)#ip address 2.0.0.2 255.0.0.0
 Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
Router(config-if)#exit
 Router(config)#interface Serial0/0/0
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
ip address 3.0.0.1 255.0.0.0
Router(config-if)#no shutdown

Step 3 Here now i am going to router in  3 and provide ip address

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface FastEthernet0/0
Router(config-if)#ip address 6.0.0.1 255.0.0.0
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#interface Serial0/0/0
Router(config-if)#ip address 1.0.0.2 255.0.0.0
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
Router(config-if)#exit
Router(config)#interface Serial0/0/1
Router(config-if)#ip address 2.0.0.1 255.0.0.0
Router(config-if)#no shutdown

 

Step 4 After ip address provide we configure static routing in router 0

Router(config)#ip route 5.0.0.0 255.0.0.0 4.0.0.2
Router(config)#ip route 1.0.0.0 255.0.0.0 4.0.0.2
Router(config)#ip route 6.0.0.0 255.0.0.0 4.0.0.2
Router(config)#ip route 2.0.0.0 255.0.0.0 4.0.0.2
Router(config)#ip route 7.0.0.0 255.0.0.0 3.0.0.1
Router(config)#ip route 2.0.0.0 255.0.0.0 3.0.0.1
Router(config)#ip route 6.0.0.0 255.0.0.0 3.0.0.1
Router(config)#ip route 1.0.0.0 255.0.0.0 3.0.0.1

Routing for Router 1

Router(config)#ip route 5.0.0.0 255.0.0.0 4.0.0.2
Router(config)#ip route 1.0.0.0 255.0.0.0 4.0.0.2
Router(config)#ip route 6.0.0.0 255.0.0.0 4.0.0.2
Router(config)#ip route 2.0.0.0 255.0.0.0 4.0.0.2
Router(config)#ip route 7.0.0.0 255.0.0.0 3.0.0.1
Router(config)#ip route 2.0.0.0 255.0.0.0 3.0.0.1
Router(config)#ip route 6.0.0.0 255.0.0.0 3.0.0.1
Router(config)#ip route 1.0.0.0 255.0.0.0 3.0.0.1

Routing for Router 2

Router(config)#ip route 8.0.0.0 255.0.0.0 3.0.0.2
Router(config)#ip route 4.0.0.0 255.0.0.0 3.0.0.2
Router(config)#ip route 5.0.0.0 255.0.0.0 3.0.0.2
Router(config)#ip route 1.0.0.0 255.0.0.0 3.0.0.2
Router(config)#ip route 6.0.0.0 255.0.0.0 2.0.0.1
Router(config)#ip route 1.0.0.0 255.0.0.0 2.0.0.1
Router(config)#ip route 5.0.0.0 255.0.0.0 2.0.0.1

Routing for Router 3

Router(config)#ip route 5.0.0.0 255.0.0.0 1.0.0.1
Router(config)#ip route 4.0.0.0 255.0.0.0 1.0.0.1
Router(config)#ip route 8.0.0.0 255.0.0.0 1.0.0.1
Router(config)#ip route 3.0.0.0 255.0.0.0 1.0.0.1
Router(config)#ip route 7.0.0.0 255.0.0.0 2.0.0.2
Router(config)#ip route 3.0.0.0 255.0.0.0 2.0.0.2
Router(config)#ip route 8.0.0.0 255.0.0.0 2.0.0.2

IF you will have any problem in this routing you can download static routing lab click to this link download  ,

thank you

by vishnu sharma

 

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s